How To Replace A Bathtub (For Newbies).
How To Replace A Bathtub (For Newbies).
Blog Article
The article down below involving How to Install a Bathtub is fairly insightful. Don't skip it.
Mounting a bathtub isn't precisely brain surgery, yet it does require solid plumbing, woodworking, and also sometimes, tiling skills. Changing an old bath tub with a new one is likewise a reasonably tough task. If the old tub is readily easily accessible, the job can relocate quickly; if you have to open up a wall to eliminate the old bathtub and also position the new bathtub, the task is a lot harder. In either situation, the task is within a home handyman's skills, although you will need an assistant to vacate the old bathtub and also set in the new one. Ensure you have qualified on your own for the task and also fit trying it. As opposed to hiring a contractor to take over a halfway-completed job, it is much better to think about utilizing one before you begin. Possibilities are you may need an expert plumber to make tube connections.
This post will help you install a new bathtub in your restroom if you have already bought a new tub and do not require to transform the setup of your previous water pipelines.
Your tools as well as material checklist should comprise the following:
Planning for the Installment
To start with, the supporting frame supplied with the bathroom must be fitted (if needed) according to the producer's directions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to make certain that if the tap features a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets system to prevent pressure on the bathtub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to now prepare to be suited its final placement.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the water system. After doing so, turn on the taps to drain pipes any water staying in the system. The procedure of getting rid of the existing taps can be rather bothersome due to the restricted gain access to that is often the case.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a towel all set for the remaining water that will originate from the pipelines. Once the supply pipes have actually been gotten rid of, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming throughout this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any kind of old securing compound.
Before proceeding to fit the brand-new faucets, contrast the pipeline connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Installing the Tub
Utilizing both wood boards under its feet, position the bath tub in the required position. The wooden boards are useful in uniformly spreading out the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following goal is to make certain that the bath tub is leveled all round. This can be attained by examining the level and readjusting the feet on the tub up until the level checks out level.
To install taps, fit the bottom of the furthest flexible tap connector to the appropriate supply pipe by making a compression join; after that do the very same for the various other faucet.
Turn on the water system as well as inspect all joints and new pipework for leaks and tighten them if necessary. Load the bath tub as well as likewise inspect the overflow outlet as well as the normal outlet for leakages.
Finally, fix the bathroom paneling as explained in the producer's instruction manual. Tiling and also sealing around the bathtub needs to wait up until the tub has been made use of at least when as this will certainly settle it right into its final position.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic connector to stop damage to the thread. One end of the port fits on the plastic tail of the tap and also the other end provides a link to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly require reducing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the installing opening in the bath/basin making sure that the washers remain in place in between the tap and the sink. Safeguard the tap in position with the maker offered backnut. As soon as the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap adapters. The previous type must be connected to the faucet ends initially, tightening only by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the location where the bath fulfills the tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture a stiff seal, creating the water to permeate the wall surface between the bathroom and the tiling, causing complications with wetness and feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your components and also fittings. They are marketed in tubes and cartridges, as well as can sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked paper or soft rope. Remember to constantly load the bathtub with water before securing, to allow for the activity experienced when the tub remains in use. The sealer can crack relatively very early if you do not consider this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently readily available on the marketplace. It is advisable to fit the tiles utilizing water-resistant or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our post about Tools You Need to Install a New Bathtub . Thanks for finding the time to read our article. Are you aware of another individual who is excited about Tools You Need to Install a New Bathtub ? Do not hesitate to share it. Thanks a bunch for your time. Visit us again soon.
Free Estimate Report this page